Introduction To Fiber Laser Marking

This post is a reprint of an article that appeared on Photonics Online.

Laser Marking Basics

Laser marking is like burning leaves with a magnifying glass.

In order to burn a leaf with a magnifying glass, one places a simple lens over the leaf at the focal point of the lens and lets the lens collect the rays of the sun. The sunlight collected by the lens then focuses on the leaf and concentrates sunlight on a small spot on the leaf. Then, bingo! The resulting heat causes the leaf to smoke and eventually catch fire.

LANGOLIER_Class_IV-resized-261.jpgLaser marking systems employ exactly the same principle. Instead of sunlight being passed through a simple lens, however, laser light is passed through a more complex lens — an f theta lens. While sunlight consists of many colors or wavelengths, laser light has the property of being monochromatic, meaning that laser light is all the same color or wavelength. The wavelength depends on the type of laser. Different materials absorb different wavelengths of light. If the material placed under the laser happens to absorb the wavelength of that laser, then there is a good match.

For laser marking applications, the laser beam is focused onto the surface of the material to be marked with an f theta lens. An f theta lens has the property of being able to maintain its focus throughout a plane, rather than focusing on just one spot. The laser beam is steered through the f theta lens by a pair of computer-controlled mirrors. The laser beam can be focused on the material anywhere within the plane defined by the f theta lens, and if there is a good match between laser wavelength and material, the result will be a mark left on the material. That mark can be in the form of graphical images, text, machine-readable codes (i.e. barcodes, UID codes or 2D codes), or any other type of mark imaginable.

Different laser types are suitable for different materials. If one wanted to mark wood, for example, the optimum wavelength of light for that material is that produced by a CO2 laser. If one wanted to mark metals, the optimum wavelength would be that produced by a YAG or fiber laser. The material to be marked dictates the type of laser that is needed. There is no such thing as a laser that is well-suited for all materials.

For a demonstration of a laser marker in action, check out the video below:

 

How To Use A Fiber Laser Marker

The following is a brief description of how to use a fiber laser marker and is only intended to “jump start” a new user. It makes the assumption that the marker has a steered beam (galvo-driven) optical system.

Before you begin to mark something, first you have to answer the following three questions:

  1. What you are going to mark?
  2. Where are you going to mark it?
  3. How are you going to mark it?

What you are going to mark and where you are going to mark it have to do with the specific laser marking software that you are using. Jimani Langoliers use Prolase Laser Marking Software exclusively, and you can learn more about the software by viewing the Prolase 7 Fiber Laser Marking Software Tutorial.

Generally, the most challenging question to answer for new users is, “How are you going to mark it?” To address that question, one needs to know a bit about how the fiber laser and the marking system work.

If you are familiar with laser marking, then you probably know that the three most important settings that can be changed to affect how a part is marked are:

1. Speed

This is how fast the laser beam travels over the part being marked. Steered beam systems use scanning galvanometers with mirrors attached to them to move the laser beam through the lens and over surface of the part. The galvos can usually steer the laser beam over the part much faster than the laser has the ability to mark the part appropriately, so galvos rarely run at their maximum potential speed. Galvo manufacturers will give speed specifications that state that the galvo is capable of “hundreds of characters per second.” At those speeds and for most materials, however, the laser does not have enough time on any portion of the part to do any work. Useful speeds depend on the material and the laser power. Speeds of 30 to 35 inches per second might be fine for removing anodize on aluminum, but engraving deeper into metals will be better accomplished at a speed of 5 inches per second, making multiple passes over the part.

2. Power 

The laser can only put out as much power as it is designed for. Generally speaking, more power out of the laser will allow either more material removal or allow the part to be marked at higher galvo speeds. In a Jimani Langolier marker, power is calibrated in watts. A 20 watt laser can only put out 20 watts. The appropriate power to use depends on the material being marked and the desired result. Clear polycarbonate, for example, will get a black surface mark with only 3 or 4 watts of laser power.Anodize can be ablated off the surface of an aluminum substrate with 12 to 15 watts of laser power, producing a very white mark. Deep engraving into steel (say .015 to .020” deep) requires every watt of power capable of being produced by a 50 watt fiber laser.

3. Pulse Frequency 

Unless you have a CW laser (and you won’t have one of those if your laser is used for marking), the laser puts out pulses of light rather than a continuous beam of light. Each of these pulses has a very short duration, and the time of the pulse is measured in nanoseconds. Fixed pulse width fiber lasers are only capable of producing laser pulses with the same time duration (pulse width) for each laser pulse, although they are capable of varying the number of those pulses produced each second (pulse frequency). Changing the pulse frequency affects the number of laser pulses striking the part at any location and the amount of laser energy in each of those pulses. Lower pulse frequencies tend to vaporize material because of the higher energy content of each pulse. Higher pulse frequencies tend to heat the surface of the part rather than vaporizing material from it. Heating the surface of certain materials such as steel or titanium can produce some interesting results. Rather than vaporizing material away, the heat from higher pulse frequencies can cause an oxide layer to form, producing a highly visible permanent marking without damaging the surface of the material (see Figure 1).

clear laser marking.png

A variable pulse width fiber laser can cause each laser pulse to be on for a longer or shorter period of time, yielding results like oxide layers of various colors.  Very short laser pulse widths make it possible to mark materials that would otherwise melt with longer laser pulse widths, such as certain types of plastic.

As the output pulse frequency decreases, the energy in each laser pulse increases. The laser and its associated internal optics have an energy damage threshold, and great care is taken to ensure that the output energy is not allowed to exceed the damage threshold of the laser or any of its internal components. Fixed pulse width fiber lasers have a damage threshold of about 1 mj of energy. A 20 watt fixed pulse width fiber laser will approach 1 mj of energy per pulse at a pulse frequency of about 20 KHz and 20 watts of output power. Because of this, a 20 watt fixed pulse width fiber laser is not allowed to work at pulse frequencies lower than 20 KHz.

Remember, output energy increases as pulse frequency decreases. So, a 20 watt fixed pulse width fiber laser will have the maximum possible energy per pulse at a 20 KHz pulse frequency. Setting the pulse frequency lower than 20 KHz will not result in more energy per pulse because the laser is internally restricted from pulsing at lower frequencies. A typical pulse frequency range for a 20 watt fixed pulse width fiber laser is 20 to 200 KHz. The useful pulse frequency range is approximately 20 to 50 KHz. At pulse frequencies higher than 50 KHz, there is not enough energy produced in each pulse to do much work. A 50 watt fixed pulse width fiber laser approaches 1 mj per pulse at 50 KHz pulse frequency and 50 watts of output power, so it is internally restricted from operating at lower frequencies.

The useful pulse frequency range of a 50 watt fixed pulse width fiber laser is about 50 to 80 KHz. Again, above 80 KHz there is just not enough energy in each pulse to do much work. Variable pulse width fiber lasers are allowed to operate at lower pulse frequencies, although they still have that same 1 mj per laser pulse damage threshold.

If a lower pulse frequency is selected on a variable pulse width fiber laser, the laser power output is internally reduced so that the energy per pulse cannot exceed the damage threshold. There is no getting around the damage threshold. It’s physics.

So, how material marks is a function of how fast the laser beam is moving over the part, how much power the laser is putting out, and the pulse frequency that the laser is operating at. Lower speed, higher laser power, and lower pulse frequencies result in stronger and deeper marking. Conversely, higher speed, lower laser power, and higher pulse frequencies result in weaker and shallower marking.

Since the laser beam is pulsed as it moves over the work, a line drawn by the laser might look like this:

oooooooooooooooooooooooooooooooooooooooooooooooooooo

If either the galvo speed is decreased or the output pulse frequency is increased, the laser pulses will overlap each other.

overlapping laser.png

This means that each location on the drawn line will be impacted by more laser pulses, since those pulses overlap each other. But, if the pulse frequency is so high that the energy per pulse is significantly reduced, then the net result might be a weaker, shallower mark on the part because of the reduced energy per pulse.

There is a tradeoff between the energy per pulse and the number of overlapping pulses. There are other variables that can affect the quality of the mark such as fill density and spot size. Those topics are beyond the scope of Laser Marking 101 and are best discussed after one has a good understanding of the relationship between speed, power, and pulse frequency. 

Editor’s Note: This article was first published in Photonics Online. You can read the original article here.

{{cta(‘ba2ca0ed-28f5-4625-b1b6-d46a55829f7c’)}}

 

Leave a Reply

Your email address will not be published. Required fields are marked *

Contact Us